收藏本站
ADE7751
THEORY OF OPERATION
The two ADCs digitize the voltage and current signals from the
are sinusoidal, the real power component of the instantaneous
power signal (i.e., the dc term) is given by:
? × cos ( 60 ° )
?
2 ?
current and voltage transducers. These ADCs are 16-bit second
order sigma-delta converters with an oversampling rate of 900 kHz.
This analog input structure greatly simplifies transducer interfacing
by providing a wide dynamic range for direct connection to the
transducer and also by simplifying the antialiasing filter design.
A programmable gain stage in the current channel further
facilitates easy transducer interfacing. A high-pass filter in the
current channel removes any dc component from the current
signal. This eliminates any inaccuracies in the real power calcu-
lation due to offsets in the voltage or current signals—see
HPF and Offset Effects section.
The real power calculation is derived from the instantaneous
power signal. The instantaneous power signal is generated by a
direct multiplication of the current and voltage signals. In order
to extract the real power component (i.e., the dc component), the
? V × I ?
?
This is the correct real power calculation.
INSTANTANEOUS
POWER SIGNAL
V I
2
0V
CURRENT
VOLTAGE
INSTANTANEOUS
REAL POWER SIGNAL
(1)
instantaneous power signal is low-pass filtered. Figure 2 illustrates
the instantaneous real power signal and shows how the real power
information can be extracted by low-pass filtering the instantaneous
power signal. This scheme correctly calculates real power for
INSTANTANEOUS
POWER SIGNAL
INSTANTANEOUS
REAL POWER SIGNAL
nonsinusoidal current and voltage waveforms at all power factors.
All signal processing is carried out in the digital domain for
superior stability over temperature and time.
V I
2
cos(60 )
0V
HPF
DIGITAL-TO-
FREQUENCY
F1
VOLTAGE
60
CURRENT
CH1
PGA
ADC
LPF
F2
Figure 3. DC Component of Instantaneous Power Signal
MULTIPLIER
DIGITAL-TO-
FREQUENCY
Conveys Real Power Information PF < 1
CH2
ADC
CF
Nonsinusoidal Voltage and Current
The real power calculation method also holds true for nonsinu-
soidal current and voltage waveforms. All voltage and current
INSTANTANEOUS
POWER SIGNAL – p(t)
INSTANTANEOUS REAL
POWER SIGNAL
waveforms in practical applications will have some harmonic
content. Using the Fourier Transform, instantaneous voltage
V I
p(t) = i(t)
v(t)
and current waveforms can be expressed in terms of their
V
2
I
WHERE:
v(t) = V
i(t) = I
p(t) = V
cos( t)
cos( t)
I { 1+cos(2 t)}
2
V I
2
harmonic content.
∞
v ( t ) = V O + 2 × ∑ V h × sin( h ω t + α h )
h ≠ 0
(2)
TIME
Figure 2. Signal Processing Block Diagram
The low-frequency output of the ADE7751 is generated by
accumulating this real power information. This low frequency
inherently means a long accumulation time between output
pulses. The output frequency is therefore proportional to the
average real power. This average real power information can in
turn be accumulated (e.g., by a counter) to generate real-energy
information. Because of its high output frequency, and hence
shorter integration time, the CF output is proportional to the
instantaneous real power. This is useful for system calibration
purposes that would take place under steady load conditions.
Power Factor Considerations
The method used to extract the real power information from the
instantaneous power signal (i.e., by low-pass filtering) is still
valid even when the voltage and current signals are not in phase.
Figure 3 displays the unity power factor condition and a DPF
(displacement power factor) = 0.5, i.e., current signal lagging
the voltage by 60 ° . If we assume the voltage and current waveforms
where:
v ( t ) = The instantaneous voltage
V O = The average value
V h = The rms value of voltage harmonic h
and
h = The phase angle of the voltage harmonic
∞
i ( t ) = I O + 2 × ∑ I h × sin( h ω t + β h ) (3)
h ≠ 0
where:
i ( t ) = The instantaneous current
I O = The dc component
I h = The rms value of current harmonic h
and
h = The phase angle of the current harmonic
–10 –
REV. 0
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
EVAL-ADE7752AEBZ BOARD EVALUATION FOR ADE7752A
EVAL-ADE7753ZEB BOARD EVALUATION AD7753
EVAL-ADE7754EBZ BOARD EVALAUTION FOR ADE7754
EVAL-ADE7755ZEB BOARD EVALUATION FOR AD7755
EVAL-ADE7758ZEB BOARD EVAL FOR AD7758
EVAL-ADE7759EBZ BOARD EVALUATION FOR ADE7759
EVAL-ADE7762EBZ BOARD EVALUATION FOR ADE7762
EVAL-ADE7763ZEB BOARD EVALUATION FOR ADE7763
相关代理商/技术参数
EVAL-ADE7752AEB 制造商:Analog Devices 功能描述:EVAL BD THREE PHASE ACTIVE ENERGY MET IC - Bulk
EVAL-ADE7752AEBZ 功能描述:BOARD EVALUATION FOR ADE7752A RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081
EVAL-ADE7752EB 制造商:AD 制造商全称:Analog Devices 功能描述:Three Phase Energy Metering IC with Pulse Output
EVAL-ADE7753ZEB 功能描述:BOARD EVALUATION AD7753 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081
EVAL-ADE7754EB 制造商:Analog Devices 功能描述:EVALUATION BOARD FOR POWER METERING, POLYPHASE MULTIFUNCTION ENERGY METERING IC WITH SERIAL PORT 制造商:Analog Devices 功能描述:PWR METERING, POLYPHASE MULTIFUNCTION ENERGY METERING IC W/ - Bulk
EVAL-ADE7754EBZ 功能描述:BOARD EVALAUTION FOR ADE7754 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081
EVAL-ADE7755EB 制造商:Analog Devices 功能描述:EVAL BOARD ENERGY METERINGW/PULSE OUTPUT - Bulk
EVAL-ADE7755EBZ 制造商:AD 制造商全称:Analog Devices 功能描述:Energy Metering IC with Pulse Output